PAINTS - Indoor paints - ORIGO indoor dispersions base wall paint

Indoor
Can be applied with cotton roller
Can be applied with paint brush
Can be applied with airless spray gun
Can be thinned with water
Packaging
Pallet

ORIGO indoor dispersions base wall paint

  • Indoor dispersions base wall paint,
  • premixed in the factory,
  • having a mat appearance.

It is suitable to coat indoor plastered, filled, concrete, gypsum, plasterboard, asbestos cement and brick surfaces of old and new buildings. Its coating is aesthetic. It does not hinder the natural ventilation of the wall, it has a good valour permeability.

Available only in white colour.
Colouring: Not recommended

The ORIGO indoor dispersion wall paints are suitable for coating indoor plastered, filled, concrete, asbestos cement and brick surfaces of new and old buildings. Its coating is aesthetic. It does not hinder the natural ventilation of the wall, it has a good air and vapour permeability.

The substrate shall be free from dust and dirt, and the full layer thickness shall be dry. In case of plastered surface and concrete wall the substrate shall be load bearing, as well as free from movement and shrinkage. In case of painting old surfaces, remove the lose, damaged layers and paint residue, and scrape out larger cracks. Repair the surface defects, use overlapping strengthening bands at the crack and at the joints of plasterboards and dissimilar materials. Make sure that the structure of the repaired surface is the same as that of the existing surface.

It is necessary to use REVCO PRIMER wall impregnating agent before applying paint on whitewashed or absorbent substrate (such as old plastering, porous concrete, repaired base plastering). Remove dust caused by previous operation or by other reason from the surface. Agitate the wall paint before starting the application by means of blades attached to slowly revolving drilling machine.

Tools: brush, roller or spray gun

Spreading: Make sure to spread the material uniformly!

Required quantity: ~10 m2/l is recommended in one layer.

The hiding power of ORIGO indoor dispersion wall paint depends on the substrate, it is recommended to use two layers among normal conditions. Increasing thinning tends to reduce the hiding power, as well as the adhesion and wear strength of the material. The specified quantities refer to smooth substrate. The quantity required for rough surfaces should be checked on site. We cannot assume responsibility regarding the required quantities. This product is available only in white colour.

Thinning: with max. 10 % water.

Colouring: Not recommended!

Temperature: The temperature of air and wall surface shall be between +5 °C and +25 °C.Do not apply the material at places affected by drought!

Total drying time: 2 h
The specified values are valid at a temperature of 20 °C and a relative humidity of 42 %. The application properties may be significantly longer if the weather changes (low temperature, high humidity content).

Overcoating interval: min. 12 h

Cleaning: With dry cloth.

Storing: One year in original packaging at place free from freezing. Carefully close the bucket after using.

Density (at 20 °C): 1.50 g/cm3

Non volatile part: ~60 % (m/m) (at 105 °C, 3 h)

Packaging: 15 l, 2.5 l

Fire hazard class: Not flammable. Belongs to fire hazard class E

Permit: Kermi 2008/2-000313-1

While drying, the agent must be protected from direct sunlight, draught, frost, driving rain, and temperatures above 30°C. Please refer to the label on the bucket and the technical information for the agent before application. Our technical specification is based on the premise that our products are used by trained professionals. The product and the information leaflet have been produced on the basis of our latest experience and knowledge, but this does not exempt the user from carrying out preliminary practical tests and colour checks. After starting the application, no complaints with respect to colour shall be accepted.

The colours on the sample materials are for information only; due to the differences in application and weather conditions, a complete colour match cannot be guaranteed.

Avoid contact with skin and eyes; in case of contact, rinse thoroughly with water and consult a doctor if necessary.

Related documents

Declaration of performance

Products

Wall paints, glazes, plasters, supplementary items and thermal insulations systems ...
MORE